|Published (Last):||22 August 2006|
|PDF File Size:||2.36 Mb|
|ePub File Size:||1.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
The low harmonic distortion and low noise make the TL07x series ideally suited for high-fidelity and audio preamplifier applications. Each amplifier features JFET inputs for high input impedance coupled with bipolar output stages integrated on a single monolithic chip. The I-suffix devices are characterized for operation from?
The M-suffix devices are characterized for operation over the full military temperature range of? Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Products conform to specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all parameters. On products compliant to MIL? On all other products, production processing does not necessarily include testing of all parameters. Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www. NC IN? OUT 64? C1 18 pF ? Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less. The output may be shorted to ground or to either supply. The package thermal impedance is calculated in accordance with JESD All characteristics are measured under open-loop conditions with zero common-mode voltage, unless otherwise specified. Pulse techniques must be used that maintain the junction temperature as close to the ambient temperature as possible.
Input bias currents of an FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive, as shown in Figure 4. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. VO Figure 1. Unity-Gain Amplifier Figure 2. Figure 3. Maximum Peak Output Voltage? IB Input Bias Current?
Free-Air Temperature? Hz 1M 10 M??? Hz 4M 10 M Figure 6 Figure 7? Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. Load Resistance? Large-Signal Differential Voltage Amplification? Supply Voltage? Common-Mode Rejection Ratio? Supply Current Per Amplifier?
Total Power Dissipation? TL TA? Equivalent Input Noise Voltage? Total Harmonic Distortion? Input and Output Voltages? Input 0 0. Output Voltage? Elapsed Time?
Output A 1? F Input k? F k? Figure OUT Figure AC Amplifier 18? NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. Samples may or may not be available. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
All linear dimensions are in inches millimeters. This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Index point is provided on cap for terminal identification only. This package can be hermetically sealed with a metal lid.
The terminals are gold plated. All linear dimensions are in millimeters. Body dimensions do not include mold flash or protrusion not to exceed 0, Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components.
To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices.
Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
amplificador operacional tl071
TL071CP - TL071 Low Noise JFET Op-Amp
Аналоги для tl071