EVAM 17112 PDF

Sajora B Acid bessemer steel only. NOTE 4—Purchasers are cautioned that different classes of nuts have different nut thickness see 7. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition see 5. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Others are not suitable. Zinc-coated nuts are nuts intended for use with externally threaded fasteners which are hot-dip zinc-coated, mechanically zinc-coated, or have a plating or coating of sufficient thickness to necessitate overtapping the nut thread to provide assemblability.

Author:Fenrim Goltiran
Country:Malta
Language:English (Spanish)
Genre:Environment
Published (Last):20 February 2013
Pages:110
PDF File Size:20.68 Mb
ePub File Size:11.6 Mb
ISBN:781-5-15464-432-7
Downloads:25926
Price:Free* [*Free Regsitration Required]
Uploader:Kajikinos



Sajora B Acid bessemer steel only. NOTE 4—Purchasers are cautioned that different classes of nuts have different nut thickness see 7. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition see 5. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn.

Others are not suitable. Zinc-coated nuts are nuts intended for use with externally threaded fasteners which are hot-dip zinc-coated, mechanically zinc-coated, or have a plating or coating of sufficient thickness to necessitate overtapping the nut thread to provide assemblability. Selection of the class shall be at the option of the manufacturer.

When this heat treatment is used, there shall be particular attention to the requirements in 6. Zinc-coated nuts are nuts intended for use with externally threaded fasteners which are not hot-dip zinc-coated, mechanically zinc-coated, or have a plating or coating of sufficient thickness to necessitate asrm the nut thread to provide assembiability. When required, they are covered by the applicable bolt specification.

NOTE 6—It is the intent of 4. Link to Active This link will always route to the current Active version of the standard. ASTM AM Specification F, or otherwise hot-dip coated, shall be tapped oversize by a diametral amount sufficient to permit assembly on the coated bolt thread, unless other requirements are specified in the inquiry or purchase order.

Heat analysis Product analysis Copper: This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Class 9 nuts in nominal thread diameters M42 and larger shall conform to dimensions for heavy hex nuts given in ANSI B A number in parentheses indicates the year of last reapproval. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Heat analysis Product analysis Titanium: Please help us to share our service with your friends. Heat analysis Product analysis Sulfur: Classes 8S3 and 10S3 nuts have atmospheric corrosion resistance and weathering characteristics comparable to those of the steels. Selection of steel analysis shall be the option of the manufacturer. Heat analysis Product analysis Vanadium: Heat analysis Product analysis Manganese: With the written approval of the purchaser, the supplier may substitute as follows: A superscript epsilon e indicates an editorial change since the last asfm or reapproval.

Heat analysis Product analysis Chromium: Class 10 nuts are made of carbon or alloy steel conforming to chemical composition requirements given in Table 1, and are heat treated as specied in 4.

We need your help! Note 1 — Throughout this specification, the term class means property class. Dimensional suitability of the nut for the intended application should be considered before approving substitution aztm a higher class. NOTE 7—The proof load of a nut is the axially applied load the nut must withstand without thread stripping or rupture. For the convenience of the asfm, Committee F16 has highlighted those changes that impact the use of this standard. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

The lubricant shall be applied to specified surfaces on the nuts, such as 1 principally only those portions which are threaded, or 2 on threaded portions and either only one bearing face or both bearing faces, as required, or 3 such other specific lubricant placement criteria as are agreed to between the purchaser and the user.

Hex jam nuts are not normally proof load tested. Committee F16 has identified the location of selected changes to this standard since the last issue A—07 that may impact the use of this standard. Heat analysis Product analysis Nickel: Additional tests of individual shipments of material are not ordinarily contemplated.

Nominal Nut Size, in. Most Related.

ISBN 0393967131 PDF

EVAM 17112 PDF

Yozshukora You are responsible for reading through each lab prior to class. If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. A working-class Italian-American bouncer becomes the driver of an African-American classical pianist on a tour of venues through the s American South. There are no make-ups for missed labs in or Moodle.

JOSEPH TURRIN CAPRICE PDF

APOSTILA CRISTOLOGIA PDF

Mall The final, the eighth chapter contains the organs of special senses, as olfaction, vision, hearing and equilibrium. Organs of the head, the neck, those of the thoracic and abdominal cavities, pelvic and perineal organs follow each other in chapter six. The presentation of the anatomy and embryology of the cardiovascular and lymphatic systems in chapter five anztomia with the heart and concludes with the distribution of the lymph vessels. His book started with funkcionaois chapter of basic embryology and as second chapter, was followed by basic histology. The anatomical demonstration is followed by the description of the microscopic structure of the organs. The parallel and interrelated development of organs with close topographical relations nevertheless of different visceral systems — e.

KEITHLEY 2636A MANUAL PDF

ENTREPRENEURSHIP BY DONALD F KURATKO PDF

Tam Thanks for your feedback, it helps us improve the site. Is all laptop fan with 3 needle compatible with all laptop motherboards exmpl. Our core value is to be one of the Top 3 professional manufacturers in replacement Laptop Battery and other electic products with our dedication, efficiency, meticulousness and innovation. My problem is solved TUVM! You can also refer to the following link: But this would not drastically reduce the temperature of a Pentium 4 based laptop. The install will fail unless this compatibility is chosen. You can ensure product safety by selecting from certified suppliers, including 4 with ISO certification.

Related Articles